Viton
1. VITON TWO PACK ACRYLIC
A Premium Two -Pack Acrylic auto finish with excellent resistance to chemicals and mechanical abrasion and a superb high gloss finish, formulated to withstand the most severe tropical climatic conditions. VitonTwo Pack Acrylic Enamel is suitable for general use on all types of car repair jobs, particularly recommended as an automotive top coat where a superior finish, offering maximum physical and chemical resistance, is required. For best results, VitonTwo Pack Enamel
should be applied over VitonTwo Pack Acrylic Primer (Beige).
PHYSICAL DATA:
SOLIDS: 60%-62% (by weight).
SUPPLY VISCOSITY: 110 -115 seconds 64/25 ºC.
DRY FILM THICKNESS: 40-45 Microns.
HARDNESS: 4H (after 24 hours).
GLOSS: 94%AT 20 degrees.
COLOUR: Arange of solid colours & metallic silver.
FLEXIBILITY: Passes Conical Mandrel (7mm) after 24 hours.
PACK SIZES: 4 litres and 1 litre (Hardener available in 1 litre and 0.25 litre)
CHEMICAL CHARACTERISTICS:
ACID RESISTANCE: Passes 0.1 (N) H2S04 for 2 hours at 30 degrees C.
PETROL RESISTANCE: Passes 4 hours immersion at 25 degrees C.
HUMIDITY AND SALT: Passes 168 hours and 96 hours respectively.
SPRAY (As per ASTM specification)
PRIMER: Viton Two Pack Acrylic Primer (see separate Data Sheet)
APPLICATION:
NO.OF COMPONENTS: Two (Base and Hardener)
MIXING OF RATIO: 4 parts Base : 1 part Hardener: 1 part Thinner (by volume)
APPLICATION RATIO: By conventional spray at a viscosity of 20 -22 seconds B4/25ºC & Spray
Pressure of 45 -50 PSI.
DRYING TIME:
SURFACE TEMP TOUCH DRY HARD DRY OVERCOATING / REPAIR TIME POT LIFE
15-25 ºC 1 hr 6 hrs 5-6 hrs 6 hrs
25 -30 ºC 45 min 4-5 hrs 5-6 hrs 5-6 hrs
30 -35 ºC 30 min max 3 hrs 5-6 hrs max 5 hrs 11
2. Viton Two Pack Thinner
CLEANING SOLVENT: VitonTwo Pack Thinner
STORAGE & MIXING: This product is highly susceptible to moisture and should be mixed/stored in dry, non-humid
conditions. After mixing Base, Hardener and Thinner in the correct ratio, allow to stand for 5-7 minutes for bubbles/effervescence to subside, before use.
HANDLING:
This product is toxic and care must be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves, goggles, should be worn during application.
FLASH POINT: Below 20ºC
SPECIAL INFORMATION FOR INCREASED PRODUCTIVITY, VITON TWO PACK ACRYLIC ENAMEL
CAN BE BAKED AT 60 ºC -70 “C FOR 45 MINUTES WITH A FLASH OFF TIME OF 10 MINUTES. 12 TWIGA PAINTS LTD.
3. VITON DOUBLE -STRENGTH PAINT REMOVER
This is a non -inflammable material designed to strip off old paint work from any metallic and non -metallic surface.
PHYSICAL DATA:
Consistency: Thixotropic consistency with very good application properties.
Pack sizes: Available in 5 litres and 1 litre.
APPLICATION:
VITON Double Strength Paint Remover should be applied liberally by brush and allowed to remain on the surface for 5-6 minutes to ensure maximum penetration into the existing paint film.
The paint should then be scraped off with a scraper and washed off with water. Surface must be rendered dry before painting. Repeat the exercise where necessary on old and stubborn paint work. For best results, particularly on non-metallic surfaces, allow the paint remover to remain on the surface for up to 1 hour before removal.
ADDITIONAL INFORMATION
HANDLING
This product is toxic and care must be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves and goggles should be worn during use.
4. VITON CELLULOSE ENAMEL
A single pack car finish which gives fast air dry for rapid turn around of repairs and provides a quick, economical and high quality of refinish on all types of vehicles. For best results, VITON Cellulose Enamel should be applied over VITON Primer/Surfacer (Grey).
PHYSICAL DATA:
COLOUR: A range of solid colours and metallic silver.
PACK SIZES: 4 litres, 1 litre and ½ litre
SUPPLY VISCOSITY: 112-114ku at 25 ºC
DRY FILM THICKNESS: 40-45microns
GLOSS: More than 80% at 20”
HARDNESS: Passes 2H (after 24hours)
FLEXIBILITY: 5-6 mm (Erichsen Cupping)
PRIMER: VITON Primer/Surfacer-Grey (refer separate data sheet).
APPLICATION:
NO. OF COMPONENTS: One
THINNING RATIO: 1 part paint: 1 part high gloss thinner (by volume)
APPLICATION: By conventional spray at a viscosity of 20-22 seconds B4/ 25 ºC
and spray pressure of 45-50PSI.
DRYING TIME:
SURFACE TEMP TOUCH DRY OVERCOATING TIME INTO SERVICE
15-25 ºC 10minutes 45 minutes Overnight
25-30 ºC 8-10minutes 30minutes Overnight
30-35 ºC 5-8minutes 30minutes Overnight
ADDITIONAL INFORMATION:
THINNER: VITON High Gloss Thinner.
CLEANING SOLVENT: VITON High Gloss Thinner
STORAGE/MIXING: This product is inflammable and explosive in nature,hence should be mixed and stored in a cool place and away from naked flames.
HANDLING: This product is toxic and care should be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves and goggles should be worn during application. 7 VITON
5. VITON RUBBING COMPOUND
VITON rubbing compound is specially formulated for producing an even glossier finish on VITON Cellulose Enamel.
PHYSICAL DATA:
CONSISTENCY: Thick paste.
COLOUR: Dark Yellow.
PACK SIZES: 4 Kgs 1 kg and ½kg.
APPLICATION:
Thin slightly with water to a creamy consistency using a soft cloth. Rub with considerable pressure at first, easing up gradually as the compound dries and develops the desired finish.
ADDITIONAL INFORMATION:
STORAGE: Should be stored in a cool and well-ventillated conditions
HANDLING: Care should be taken to prevent direct contact with the skin and eyes to avoid irritation.
Affected areas must be washed immediately and thoroughly with’ clean water. Protective clothing, goggles and gloves should be worn during application and sanding. 8
6. VITON FAST DRY ENAMEL
A fast -drying synthetic top coat for repair and complete respray of cars, vans and commercial vehicles. It offers high opacity and good flow and gloss from the gun. Recommended for use over VITON Primer/Surfacer (Grey).
PHYSICAL DATA:
COLOUR: A range of ready -mixed colours and toners.
PACK SIZES: 4 litres, 1 litre and ½ litre
SUPPLY VISCOSITY: 115 -120 seconds B4/25 ºC
DRY FILM THICKNESS: 30 -35 microns
HARDNESS: Passes H (after 24 hours)
GLOSS: 78 -80%at 20º
PRIMER: VITON Primer/Surfacer -(Grey) (see appropriate Product Data Sheet).
APPLICATION:
NO. OF COMPONENTS: One
THINNING RATIO: 4 parts paint: 1 part thinner (by volume)
APPLICATION: By conventional spray at a viscosity of 22 -24 seconds B4/25 ºC
and spray pressure of 45 -50 PSI.
DRYING TIME:
SURFACE TEMP TOUCH DRY HANDLEABLE DRY RECOATING TIME &
INTO SERVICE
15 -25 ºC 2 hours 4 hours 24 hours
25 -30 ºC 1 ¾ hours 3½ hours 24 hours
30 -35 ºC 1 hours 3 -3½ hours 24 hours
ADDITIONAL INFORMATION:
THINNER: VITON Fast Dry Thinner
CLEANING SOLVENT: VITON Fast Dry Thinner
STORAGE/MIXING: Should be stored/mixed in well ventilated conditions
HANDLING: This product is toxic and care should be taken to prevent direct contact wrth the skin and eyes to avoid irritation etc (Affected areas must be washed lmmediately and thoroughly with clean water) Protective clothing, gloves and goggles should be worn during application.
7. VITON SELF-ETCH PRIMER
This two -pack etching primer, based on reinforced vinyl resins is designed to provide maximum adhesion and corrosion resistance. VITON Self -Etch Primer provides excellent adhesion between ferrous and non -ferrous surfaces and subsequent coats of paint, and is particularly recommended on Aluminium. This primer should be supplemented by a coat of VITON Primer/Surfacer (Grey) to provide adequate film build.
PHYSICAL DATA:
COLOUR: Greenish yellow
PACK SIZES: 4 litres and 1 litre
SUPPLY VISCOSITY: 200-210 seconds B4 / 25 ºC
DRY FILM THICKNESS: 7-8 microns
APPLICATION:
NO. OF COMPONENTS: Two (Base and Activator)
MIXING RATIO: 1 part base: 1 part activator (by..volume)
APPLICATION: By conventional spray at a viscosity of 20” -22” B4/ 25 ºC and spray pressure of 45 -50 PSI. Etch primer should never be applied at more than 10 microns DFT and should be over -coated within 2 -2 ½ hours.
DRYING TIME:
SURFACE TEMP TOUCH DRY OVERCOATING TIME POTLIFE
15 -25 ºC 10 minutes 40 minutes 8 hours
25 -30 ºC 6-8 minutes 30 minutes 8 hours
30 -35 ºC 5 minutes 30 minutes 7 hours
ADDITIONAL INFORMATION:
THINNER: No thinner is required. Addition of activator would bring down the viscosity to 20-22 seconds B4 / 25 ºC
CLEANING SOLVENT: VITON Standard Thinner
STORAGE / MIXING: This product is susceptible to moisture and should be mixed/stored in dry non-humid conditions. After mixing base and activator in the correct ratio, allow to stand for 10 minutes before use.
HANDLING: This product is toxic and care should be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves and goggles should be worn during application. 4
8. VITON PRIMER / SURFACER (GREY)
A single pack, fast -drying cellulose primer offering high build and scratch filling properties on all types of vehicles. Good laydown and holdout properties of this primer provides a base for superior top coat gloss. On bare metal, VITON Primer/Surfacer (Grey) should be applied over VITON Etch Primer for enhanced adhesion. VITON Primer/Surfacer is recommended under VITON Cellulose Enamel and VITON Fast Dry Enamel.
PHYSICAL DATA:
COLOUR: Grey
PACK SIZE: 4 litres, 1 litre and ½ litre
SUPPLY VISCOSITY: 115-l20ku AT 25 ºC
DRY FILM THICKNESS: 45-50microns
FINISH: Matt
APPLICATION:
NO. OF COMPONENTS: One
THINNING RATIO: 1 part paint: 1 part VITON standard thinner (by volume)
APPLICATION: By conventional spray at a viscosity of 20-22seconds B4/25ºC and spray pressure of 45-50PSI.
DRYING TIME:
SURFACE TEMP TOUCH DRY OVERCOATING TIME
15-25 ºC 10minutes 40minutes
25 -30 ºC 6 -8 minutes 30minutes
30 -35 ºC 5 minutes 30 minutes
ADDITIONAL INFORMATION:
THINNER: VITON Standard Thinner.
CLEANING SOLVENT: VITON Standard Thinner.
STORAGE/MIXING: This product is inflammable and explosive in nature, hence should be mixed and stored in a cool place and away from naked flames.
HANDLING: This product is toxic and care must be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves and goggles should be worn during application. 5
9.VITON SPOT PUTTY
VITON Spot Putty is cellulose-based and suitably plasticised to give a hard yet flexible film, formulated to fill indentations noticeable after application of the primer. VITON Spot Putty is recommended over VITON Primer/Surfacer only.
PHYSICAL DATA:
CONSISTENCY: Thick paste.
COLOUR: Grey.
PACK SIZES: Available in 4 kgs. 1 kg and ½kg
APPLICATION:
This single pack putty should be applied either by knife or by putty -applicator in several thin coat with intervals of 10 minutes rather than one thick coat, to eliminate solvent entrapment.
DRYING TIME:
VITON spot putty dries thoroughly within 1 hour of application.
SANDABILITY: Excellent (after ½ hour).
ADDITIONAL INFORMATION:
STORAGE: Should be stored in cool and well -ventilated conditions.
HANDLING: Care should be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water).
Protective clothing, goggles and gloves should be worn during application and sanding.
10.VITON TWO PACK ACRYLIC PRIMER (BEIGE)
An extremely versatile high solids Two-pack Acrylic Primer (which can be used as a sanding/non- sanding primer) offering excellent corrosion resistance, film build and coverage. Viton Two Pack Primer can be applied direct to clean bare metal without any bonding coat. This product is recommended as a Primer/Primer-Surfacer under Viton Two Pack Acrylic Enamel to achieve maximum mechanical and chemical resistance with a superb gloss finish for Automotive vehicles. Major advantages of this high performance product are that it can be overcoated within 3 -4 hours and that it can obliterate small indentations/defects without using a body filler.
PHYSICAL DATA:
SOLIDS: 64%-66% (by weight)
COLOUR: Beige
FINISH: Smooth, semi-gloss
PACK SIZES: 4 litres and 1 litre (Hardener available in litre and 0.25 litre)
SUPPLY VISCOSITY: 110-120 seconds B4/ 25 ºC
DRY FILM THICKNESS: 55-60 microns (with two full coat applications)
APPLICATION:
NO.OF COMPONENTS: Two (base and hardener)
MIXING RATIO: 4 parts base: 1 part hardener: 1 part thinner (by volume)
APPLICATION: By conventional spray at a viscosity of 20-22 seconds B4/25 ºC and spray pressure of 45 -50 PSI.
SURFACE TEMP TOUCH DRY HARD DRY OVERCOATING POT LIFE
INTERVAL
15-25°C 45 minutes 5-6 hours 6 hours 6 hours
25 -30 ºC 30 minutes 3-4 hours 4 hours 5 -6 hours
30 -35 ºC 25 minutes 2 -3 hours 3 hours 4 -5 hours
ADDITIONAL INFORMATION:
THINNER: VitonTwo Pack Thinner
CLEANING SOLVENT: VitonTwo Pack Thinner
STORAGE/MIXING:
This product is highly susceptible to moisture and should be mixed/ stored in dry, non-humid conditions. After mixing base, hardener and thinner in the correct ratio, allow to stand for 5-7 minutes for bubbles/effervescence to subside before use.
HANDLING:
This product is toxic and care should be taken to prevent direct contact with the skin and eyes to avoid irritation etc. (Affected areas must be washed immediately and thoroughly with clean water). Protective clothing, gloves and goggles should be worn during application.
FLASH POINT: Below 20 “C.
SPECIAL INFORMATION FOR INCREASED PRODUCTIVITY, VitonTWO PACK PRIMER CAN BE BAKED AT 60 ºC -70 ºC FOR 45 MINUTES WITH A FLASH OFF TIME 10 MINUTES, FACILITATING OVERCOATING WITHIN THE HOUR. 10
